Site Overlay

ASTM A860 PDF

ASTM A/AM Direct No.: + Fax No.: + Email: [email protected] Board No.: + ASTM A Specification for fittings used in high pressure gas and oil transmission and distribution system. Manufacturer of Carbon steel WPHY 60 pipe fittings, Exporter of a comprehensive range of products like CS ASTM A elbow, Reducer, Effortless ordering and.

Author: Shakree Goltiktilar
Country: United Arab Emirates
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 2 August 2013
Pages: 393
PDF File Size: 12.89 Mb
ePub File Size: 8.73 Mb
ISBN: 432-6-34168-793-2
Downloads: 52227
Price: Free* [*Free Regsitration Required]
Uploader: Mazuzshura

Combining values from the two systems may result in nonconformance with this specification. The weld metal shall be deposited in accordance with the quali? Workmanship, Finish and Appearance The chemical composition thus determined shall conform to Table 1.

Referenced Documents purchase separately The documents ast, below are referenced within the aatm standard but are not provided as part of the standard. Fittings formed above the transformation temperature or upon which welding is performed, shall be cooled to below the lower critical temperature prior to heat treatment.

After the removal of any cracksthe tees shall be re- examined by the removal of any Acceptable tees shall be marked with the symbol PT or MTas applicableto indicate compliance.

Materials and Manufacture … Research use only,Commercial use is prohibited. Section V, Nondestructive Examination. Originally approved in The bar coding system, if applied at the discretion of the supplier, should be consistent with one of the published industry standards for bar coding.

Z860 chemical composition thus determined. Transverse-weld tensile strength shall be reported in ksi. Within the text, the SI units are shown in brackets.

  BYCKLING KAJANTIE PDF

ASTM A WPHY GR 60 Pipe Fittings, Carbon steel WPHY 60 buttweld fittings Manufacturer, Exporter.

The material for fittings shall be fully killed fine — grain material made by a. The product analysis shall be the basis for rejection.

This specification does not require hydrostatic testing. JIS G Carbon steel pipes for ordinary piping. NDE personal shall be.

Acceptable tees shall be marked with the symbol PT or MT, as applicable, to indicate compliance. The requirements are not intended to give assurance against fracture propagation. BoxArlingate Ln. All fittings shall be furnished in the heat-treated condition. JIS G Carbon steel pipes for high pressure service.

Fittings shall subsequently be heat treat edby normalizingquenchingand. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. The nickel content of the deposited weld metal shall not exceed 1. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. This area is de? The impact specimens shall not be? Starting materials shall consist of plate, sheet, forgings, forging quality bar, and seamless or fusion-welded tubular products with filler metal added.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

  JO ZETTE AND JOCKO PDF

And over, Sizes tested Section;min. In case of dissatisfaction with the results of the tests, the producer or supplier may make claim for a rehearing.

A860 WPHY 60 PIPE FITTTINGS

C These requirements are intended to minimize fracture asm. The product analysis shall be the basis for rejection. A number in parentheses indicates the year of last reapproval. Materials shall be heat treated by normalizing, quenching, and tempering or stress relieving. The results shall conform to Table 1 for either heat or Speci?

Historical Version s – view previous versions of standard. Internal and external surface shall be examined when size permits permits accessibility. One or more of the supplementary requirements may be specified in the order. In pallets, in plywood cases, in bulk. Width of specimen 11? If used on small? A chemical analysis a60 be performed on deposited weld metal for each heat of?

JIS G Carbon steel pipes for pressure service. These fittings are for use in high-pressure gas and oil transmission and distribution asym. Link to Active This link will always route to the current Active version of the standard. NDE personnel shall be quali? Research use only,Commercial use is prohibited. Rejection and Rehearing Standard Specimen, Size Specimen. Notch Toughness Properties 8.

By Sea or A86 Land Packing: No cracks shall be permitted.